IS-S0108 single switch system overview 7850 east gelding drive ? scottsdale, az 85260 -3420 IS-S0108 overview c.doc page 1 of 5 toll free 1.877.2buynkk (877.228.9655) ? phone 480.991.0942 ? fax 480.998.1435 www.nkkswitches.com ? email engineering@nkkswitches.com 1010 IS-S0108 single switch system revision c nkk switches 7850 e. gelding drive scottsdale, az 85260 toll free 1-877-2buynkk (877-228-9655) phone 480-991-0942 fax 480-998-1435 e-mail all rights reserved worldwide nkk switches makes no warranty for the use of these products and assumes no responsibility for any err ors, which may appear in this document, nor does it make a commitment to update t he information contained herein. smart switch is trademark of nkk switches.
IS-S0108 single switch system overview 7850 east gelding drive ? scottsdale, az 85260 -3420 IS-S0108 overview c.doc page 2 of 5 toll free 1.877.2buynkk (877.228.9655) ? phone 480.991.0942 ? fax 480.998.1435 www.nkkswitches.com ? email engineering@nkkswitches.com 1010 purpose and applications the single switch system is a plug and play indicat or device for use in an application with little to no technical or engineering know-how needed to install and opera te. when ordering the device a customer would list what images, labels and actions they want to see. the de vice would then be preloaded with the images, actio ns and responses ready to be used. the customer would simp ly need to install the device into their applicatio n via connector or soldering. please contact us with your application. if the IS-S0108 can not meet your app lication, we can design a device to meet your requirement. the single switch system can be used in many applic ations. it excels in displaying measurements such a s music volume, water flow, or illumination level. it can be used in a bank of displays where many measu rements have to be viewed at once or it can display each me asurement one by one when panel space is tight. it could have many images for displaying a continuous stream of information or it could be hooked up to a singl e measurement device with only a few associated image s. the images could just be a series of numeric dis plays or a graphical dial gauge. with the red/green/amber back lighting it can show important statuses or ch anges at a glance so an operator can know if an action is re quired. output commands could be sent out automatic ally based on user defined input levels. its panel mount design allows for easy installation. the switch ca n be used to cycle through a list of measurement displays, or toggle between two different modes, or as an on/of f switch. possible applications: ? display predefined images based on status of up to 8 total inputs. ? display the status of up to 4 analog gauges as bar graphs, percents, or predefined images. ? use it as a counter to display a number of events. ? use it as a timer to display the duration of an eve nt. ? change colors based on inputs then automatically to ggle other devices based on defined values. ? display different statuses by pressing the switch. ? use some of digital input/output lines to turn off or on a device based on the status of input/outputs or timer or counter. examples: ? a single switch system is hooked up to a device tha t drops jellybeans into a bag and a counting sensor . when the single switch system counts out a fixed nu mber of beans it then toggles another device to seal the bag, move it out of the way and get the ne xt bag. ? a single switch system is used as an egg timer wher e it is hooked up to a heating element that when th e switch is pressed the egg is cooked until the timer ends then the heating element is switched off. it could also be hooked up to a temperature senor to know th at the egg is correctly cooked. ? a single switch system is hooked up to a motor cont roller and a load sensor. when the load becomes too high the single switch system flashes red alert ing the operator that an action is required and sen ds a shut down signal to the motor controller.
IS-S0108 single switch system overview 7850 east gelding drive ? scottsdale, az 85260 -3420 IS-S0108 overview c.doc page 3 of 5 toll free 1.877.2buynkk (877.228.9655) ? phone 480.991.0942 ? fax 480.998.1435 www.nkkswitches.com ? email engineering@nkkswitches.com 1010 general system features the single switch system is useful in many applicat ions where complex information needs to be displaye d while minimizing design and installation time and c omplexity. the firmware is written based on custome r requirements. contact hassan sajadi at 877-228-9655 or engineerin g@nkkswitches.com for application consultation. features: ? 36x24 pixel graphic lcd. ? can display 3 lines of 6 characters each. ? multiple backlight color mode of operation. red, gr een, amber and various blinking. ? panel mount for easy installation. ? single pole momentary switch. ? firmware is written based on customer requirements. ? the connection to application can be via direct sol dering or a connector. ? up to 8 digital input/outputs. ? up to 4 analog to digital converters. ? i2c, spi, or uart configurations are available upon request. board photos part number attributes: IS-S0108x-xx IS-S0108 x-xx base part number unique for each application each application would have a unique part number.
IS-S0108 single switch system overview 7850 east gelding drive ? scottsdale, az 85260 -3420 IS-S0108 overview c.doc page 4 of 5 toll free 1.877.2buynkk (877.228.9655) ? phone 480.991.0942 ? fax 480.998.1435 www.nkkswitches.com ? email engineering@nkkswitches.com 1010 hardware warning: these products are esd sensitive. the esd handling procedures must be followed. the single switch system incorporates an is15abcp4c f in the panel mount housing soldered to a small controller pcb. power requirement: 9 to 15v controls overview: pot: contrast adjusts the contrast of the lcd. j1: application interface header is a 7x2 unpopulated .1?x .1? header location for application connections. pin description: pin 1 & 2: vcc voltage can be a minimum of 9v to a maximum of 15v but must remain constant once the contrast pot is set. pin 3 & 4: ground. pin 5: vdd voltage is 5v. it is generated by the onboard voltage regulator. the maximum current drawn can not exceed 10 ma. pin 10: switch status. it has a weak pull up. the pin goes to ground when switch is pressed. pins 8,9,13 & 14: can be set up as digital input /output or as analog input for analog to digital converter. these pins h ave 0.1 uf capacitor to ground each. the analog input must be in the ran ge of 0 to 5 v. pin 7: can be set up as digital input/output. this pin ha s a 4.7k pull down resistor. pin 6,11 &12: can be set up as digital input/out put. application interface header (j1) pin call outs: pin function 1 vcc 2 vcc 3 gnd 4 gnd 5 5v 6 digital i/o 7 digital i/o 8 digital i/o or analog input 9 digital i/o or analog input 10 switch status 11 digital i/o 12 digital i/o 13 digital i/o or analog input 14 digital i/o or analog input
IS-S0108 single switch system overview 7850 east gelding drive ? scottsdale, az 85260 -3420 IS-S0108 overview c.doc page 5 of 5 toll free 1.877.2buynkk (877.228.9655) ? phone 480.991.0942 ? fax 480.998.1435 www.nkkswitches.com ? email engineering@nkkswitches.com 1010 dimensions:
|
